Pad cleaning?

soapboxpreacher

soapboxpreacher

New member
Joined
Feb 9, 2014
Messages
106
Reaction score
0
How and what do you use for pad cleaning? And is it worth it or dump the pads when you are done?
 
Oh and do you need a dedicated pad cleaning solutions or can something I have around the house to clean these?
 
I like the powder versions that are mixed with water so I can soak the pads as they become loaded, then scrub them with a pad brush when done. The ones I have used are McKee's & Blackfire which have worked well. Also after thoroughly scrubbing and rinsing, I throw them in the washing machine.
 
I don’t care for any powdered type cleaner. Problem is that powders don’t always dissolve properly. That can create a problem next time you buff if one of those particles get dislodged from the pad.

I use an APC with a nylon pad conditioning brush with lots of free flowing water followed by a trip in the washing machine. Finally followed by drying on a rack velcro side up.
 
D-limonene @ 10 percent.

So, however you buy it, dilute it with distilled water to get a 10 percent solution. I have had great results with Citra-solv (probably 90 percent d-limonene) . But, usually I use Citra-Blast (50 percent d-limonene) because you don't need the quality of a citra-solv type product to clean pads. You do have to shake Citra-Blast prior to use. But, that's really no big deal.

You can use pad cleaner (or IPA ?) as a final step if you don't trust leaving possible d-limonene residue in your pads.

Keep in mind, a product like this is probably only needed if a type of sealer is in the pads. Compounds and polishes can be cleaned with a lot cheaper products.
 
I dump mine in the HE washing machine on a long cycle with steam. I pre-spray with an APC and toss them in. I use 3D Towel Kleen.

They come out good as new.

Yeah, the machine smells like car products after but I then run the same cycle with Tide washer cleaner and all is good. Been doing it this way for years.
 
I spray mine with McKee's polishing pad cleaner, agitate with a stiff brush, then plop them in a bucket of 3D Towel Kleen solution until I'm all done polishing.

After that, they come clean in the sink with little effort.
 
I've had good results with Blackfire's pad cleaner. The smell is harsh but it's the only thing I've found that'll remove HD speed. I spray it on, and let it soak for a few minutes then wash them by hand under hot water.
 
Is there a product that works on microfiber towels as well as the foam pads?

I see custmsprty and PaulMys use the 3D towel clean but it's not the only product. I'm a weekend warrior and trying not to have a bunch of products is why I ask. I was wondering if one could get away with just the 3d towel clean but would need a little extra effort with the pads when using it?
 
Of note, I tried a way to dry my pads quickly over the weekend. Air fluff in my dryer on the drying rack. Just blows room temp airnover them. 45 minutes later all 6 pads I had in there were dry. Even put them back on the rotary at full speed to see if any water would fly off, nothing.
 
Dr Oldz said:
I don’t care for any powdered type cleaner. Problem is that powders don’t always dissolve properly. That can create a problem next time you buff if one of those particles get dislodged from the pad.

I use an APC with a nylon pad conditioning brush with lots of free flowing water followed by a trip in the washing machine. Finally followed by drying on a rack velcro side up.
Click to expand...

While it is true what you say, one just has to insure the powder is fully dissolved and not too difficult to do with hot water and thorough agitation. I have used powder pad cleaners for years and never had a problem.
 
Hermes1 said:
While it is true what you say, one just has to insure the powder is fully dissolved and not too difficult to do with hot water and thorough agitation. I have used powder pad cleaners for years and never had a problem.
Click to expand...

I’d rather take zero chance of scratching paint. Feel free to use your own method but I prefer to take every precaution to remove potential issues that can harm paint. Takes a while to buff paint out but only seconds to scratch it back up to roughly quote Mike Phillips.
 
Dr Oldz said:
I’d rather take zero chance of scratching paint. Feel free to use your own method but I prefer to take every precaution to remove potential issues that can harm paint. Takes a while to buff paint out but only seconds to scratch it back up to roughly quote Mike Phillips.
Click to expand...

To each his own of course, but consider on another pad cleaning thread, of two products Mike Phillips recommends, one is a powdered product. I think your point would be better stated and helpful to others is to point out the potential for scratching the paint if not properly dissolved. I have found the Blackfire Advanced pad cleaner Mike Phillips recommends dissolves easily and quickly and has never left any scratches on the paint.
 
Hermes1 said:
To each his own of course, but consider on another pad cleaning thread, of two products Mike Phillips recommends, one is a powdered product. I think your point would be better stated and helpful to others is to point out the potential for scratching the paint if not properly dissolved. I have found the Blackfire Advanced pad cleaner Mike Phillips recommends dissolves easily and quickly and has never left any scratches on the paint.
Click to expand...

There are always a few ways to skin a cat. I just wanted to share my thought process and explain why. It doesn’t necessarily mean my method is proper or right. Doesn’t mean you process is wrong, so please don’t feel I was bashing your method.
 
Hermes1 said:
To each his own of course, but consider on another pad cleaning thread, of two products Mike Phillips recommends, one is a powdered product. I think your point would be better stated and helpful to others is to point out the potential for scratching the paint if not properly dissolved. I have found the Blackfire Advanced pad cleaner Mike Phillips recommends dissolves easily and quickly and has never left any scratches on the paint.
Click to expand...

Dr Oldz said:
There are always a few ways to skin a cat. I just wanted to share my thought process and explain why. It doesn’t necessarily mean my method is proper or right. Doesn’t mean you process is wrong, so please don’t feel I was bashing your method.
Click to expand...

You are both right, but watch out Dr. :

If Bruce comes at us with that big a$$ Dually Ram, we will all be in trouble. ;)
 
Dr Oldz said:
There are always a few ways to skin a cat. I just wanted to share my thought process and explain why. It doesn’t necessarily mean my method is proper or right. Doesn’t mean you process is wrong, so please don’t feel I was bashing your method.
Click to expand...

I agree and I do not feel my method is bashed. I just wanted to clarify and make clear to others that the powdered versions can be used safely if properly mixed. Contrary to what PaulMys said I will NOT be coming after you and him for that matter with my "big a$$ Dually Ram". He is always stirring up trouble.
 
I know this thread is a few months old, but wanted to ask you guys that toss them in the washer, are you using a cleaning agent in the washer? I have scaled up my work and while waiting for more pads I am struggling keeping them clean one at a time. I ran through about 30 pads in the last 2 days and I have 2 large jobs on Monday.

I have Blackfire pad cleaner, figured I would do a soak in warm water with some BF pad cleaner and toss them in the washer. I am just not sure if I should use any cleaner in the wash or just water. Also, hot? cold? warm?
 
PaulMys said:
I spray mine with McKee's polishing pad cleaner, agitate with a stiff brush, then plop them in a bucket of 3D Towel Kleen solution until I'm all done polishing.

After that, they come clean in the sink with little effort.
Click to expand...

In revisiting and rethinking this thread, this method has merit and worth my effort to try.
 
80e8d07dffbd0692b0900a1d31e0e65f.jpg


Here is what one of mine looks like after the McKee’s spray/scrub and a soak in the Towel Kleen solution, Bruce.


Sent from my iPhone using Tapatalk
 
You must log in or register to reply here.
Back
Top