scooterguitar
New member
- May 14, 2006
- 970
- 0
Since the PC migth not happen for awhiel, I am thinking of maybe trying the Polishin' Pal. Should I? Should I get a few more pads as well? Figure I can swing this and a few bottles of SSR.
Polishin' Pal?'s
- Thread starter scooterguitar
- Start date
Neothin
New member
- Mar 3, 2006
- 634
- 0
hand polishing, oh how i despise thee...
if you want to attempt it, go ahead. I'm warning you though, it is going to be VERY tiring. also, some polishes are going to leave some pretty bad marring behind. hand polishing won't break down the abrasives enough to finish nicely. be careful.
if you want to attempt it, go ahead. I'm warning you though, it is going to be VERY tiring. also, some polishes are going to leave some pretty bad marring behind. hand polishing won't break down the abrasives enough to finish nicely. be careful.
scooterguitar
New member
- May 14, 2006
- 970
- 0
- Thread starter
- #3
yikes.
Figured it owuld be better than my hand method.
Figured it owuld be better than my hand method.
MCA
New member
- Mar 3, 2006
- 114
- 0
The Polishing Pal is a god-send when it comes to LSP application - very ergonomic handle that made application both fast, easy, and even. However, it definitely is not a replacement for a PC (or even a cheap $20 orbital for that matter) when it comes to defect removal. As Neothin said, hand polishing just cannot generate enough movement or heat to breakdown the abrasives on some polishes. You will end up doing more harm than good - some polishes/compounds feel *gritty* - If you can't break these down, you will create micromarring on your paint (I cringe just thinking about it). If you insist on moving forward, I would try only the lighter polishes (Menzerna FPII, SSR1, *maybe* SSR2, Meg's #80). Hope this helps.
MCA
MCA
scooterguitar
New member
- May 14, 2006
- 970
- 0
- Thread starter
- #5
Yes, it does help.
I was trying to jstify the purchase, as I have no idea as to when I can get a pc.
Thanks
I was trying to jstify the purchase, as I have no idea as to when I can get a pc.
Thanks
I'm just curious..........how would you mimic a P.C. removing swirls/im perfections etc, using the P.P.? Circular motions?? back and forth motions ?? side to side motions??
BlackCoupe
New member
- Apr 23, 2006
- 525
- 0
SnipeJDM said:
Yeah, but what about the pads and the SSR? You are doing "purchase justification math" the same way I do!!!
BlackCoupe said:
A LITTLE NOTE:: One must be very carefull when they buy tools from places like kohl's, wal-mart, or on-line fly by night sites, many items are re-built / re-furbished units that may not have the original parts and internal mechanisms that make an original an original you get what you pay for......but with that said.....
he might luck out with places like kohl's etc........
Buyer beware.....
Last edited:
scooterguitar
New member
- May 14, 2006
- 970
- 0
- Thread starter
- #11
Yes, it's hte $ factor for me! I gotta buy a new lawn tractor tomorrow, getting married soon, and grad skewl classes. Imagine I'll just sell a few small itmes and save up for a pc and be doen with it!
Thanks for all yoru help
Thanks for all yoru help
scooterguitar
New member
- May 14, 2006
- 970
- 0
- Thread starter
- #14
Well, we are getting married at Graceland! I picked that :>)
ScottB
New member
- Mar 3, 2006
- 18,803
- 0
scooterguitar said:
last choice you will ever make ... (wife looking over shoulder) .... Congratulations on your impending numptials ..... (wife leaves) ..... why should you be any happier than the rest of us !!!! :applause:
hint ---- wedding gifts = $$$ = household items, like a buffer
scooterguitar
New member
- May 14, 2006
- 970
- 0
- Thread starter
- #16
"hint ---- wedding gifts = $$$ = household items, like a buffer"
I tried to get her to let us register at the local HD shop! It was a no go.
I tried to get her to let us register at the local HD shop! It was a no go.
