Recent content by Slowcorrado

Well, the day has come.... Today's update is the LAST panel to actually get a compound cut! It took me a few evenings longer than I expected because I had to remove the large, old, dried-out paint protection film in front of the rear wheel. With that gone though it was just the normal steps...

Soooo.. it's been a while! I'm still here and still working on the car. Life gets in the way sometimes though. I'm still looking for an original red fender if anyone knows of a source, please PM me. I'm also looking for suggestions for a LSP. My goal would be to finish out the cut process...

Sorry it's been a while... There's been progress, just not a lot! Today's update is a duplicate of one from a couple of weeks ago. The lower rocker panel trim was damaged by someone not raising the car properly on a lift. To repair this, I had to pull the trim off, release the bend using a...

Well, it's on to the passenger's fender. An extra evening was spent removing the damaged rock-protection film behind the wheel. Then, the same multi-step process was applied like I've done in the past. I found a few deep scratches and learned that I still need to learn the proper way to deal...

Thanks for the suggestions! To answer a few of the questions, as a follow-up to the suggestions: I tried an IPA, no change (no damage though) Heh. It seems to be on top of the paint, not really rough feeling, but a satin/dull texture. It looks slightly raised rather than a thin spot. The...

I totally agree RippyD! But it still grates on you a little when it's your car right? :-) Question time!!!! I've been having issues where the panels meet with dark "marks" or some type of residue. The clay bar doesn't touch it, the Meguiars #7 doesn't touch it, the Ultimate compound seems...

Thanks for the comments, I'm learning a lot too! Today's job was to finish the hood. It took a couple of evenings because I ended up doing 2 complete passes on it with the UC. The pics make it look a little better than it really looks under my LED lights. There are still lots of mid-sized...

2nd half of the day's work: I decided to start on the hood. It's a mess. It has the worst original paint on the car and is the largest panel. I'm doubting my ability to bring this back! To simplify things I removed the washer nozzles. That was a treat! They are installed in typical German...

Thanks Scott! I get excited about the results and then demoralized by the damage found under the coating of flat red. It's been a great learning experience so far and I'm not even half done. Today's update will be split into two posts. I spent like 4 hours on it and got multiple things...

Thanks for the kind words everyone. I feel like I need to post a disclaimer though: The pictures make it look better than it really does in person. :-) There are still flaws all over. I'm sure my work isn't as even as it could be, etc... in my defense though, I'll refine it further when I...

Another weekend update: It's been a few days since I've posted. Lots of life happening at the moment. But I've also tried to stop posting every little detail/step. :-) Today's update is showing the progression on the driver's side. I was able to clean/clay the remainder of the rear quarter...

I know, this update seems like cheating... But I needed an easy day today. Decided to clean the rear glass. Wiped it down and washed it. It still felt like sandpaper! Went over it with the clay bar and it worked like a charm. Slick and smooth! Then I did a pass with the Ultimate Compound...

So, it's been a couple days..... Not because I was lazy and didn't post; but because I ran into my 1st real challenge. The roof paint is just demolished. I did 4 M7 coats with vigorous manual application, then cleaned it all off and had to use UC for 2 full passes/sessions to get it to be...

Sat night update: Moving on to the next section; the roof. WOW, what a mess. I am a little disappointed in the condition of what's up here. I cleaned and ran the clay bar over everything and was rewarded with some large flaws. The previous owners have completely buffed through the hard...

Taking a break from my detailing to update this for the site admins: I'm an IT consultant and have been running into the exact same issue the other folks have been describing. Ran autogeekonline.net through some tools and found this: Scan Results - Free Website Malware Scanner "Malware...