Search results

Yup, because of my schedule I couldn't apply the coating right after Essence was used to polish the previously failed attempt of Mohs. It was about 3 hours in between.....

Thanks for your reply. Can you explain the increase in static after the coating is being wiped off? Have you experienced something similar with other coatings? I agree with you that the temp may be the root of the problem, but it also means that Mohs is definitely not as user friendly...

Thanks so much for your detailed reply. A few days ago I posted in a different thread on my first Moh's problem https://www.autogeekonline.net/forum/auto-detailing-101/116211-gyeon-mohs-problem.html The car has been sitting in the garage for more than 2 weeks so I believe whatever the temp is...

Have used Cquartz UK about 3 years ago on this particular car and I thought it was time to try something different. Well, first try it wasn’t successful as the surface area became cloudy/hazy right after I applied the second coat. Please see my other thread about this issue. Then, the second...

BTW the entire area was wiped down 3 times using Eraser, with each time leaving the Eraser on the surface for an extended period of time. So, I believe the surface was as bare as humanly possible. I had used Cquartz and Cquartz UK previously and both left a little bit of oily residue (like...

The cloudiness is present on a few areas, not the entire coated area. And the cloudiness appeared right after I applied the second coat. Did not see anything after the first coat. I thought I had removed all of the product after the 1st coat was wiped..,..

You may be right. The instructions say wait at least an hour but maybe that's under perfect conditions. I only waited an hour and definitely should have waited a lot longer, but I don't have all of the time in the world....

It is about 56 degrees in my garage with the humidity of 57%. I applied Gyeon Mohs today to the rear bumper of my car following the instructions to the T. After I wiped off the second layer after 1 hour of waiting from the first coat I noticed the paint at some areas is cloudy. I believe...

Thanks Mike for your reply. I have been a big fan of yours since the beginning of time.

The photos on the first page are no longer available.....

What's everyone's thought on mixing clear and basecoat 1:1? Would that make the final repair shiner instead of dull?

My other car is the same color and I did apply multiple layers. Perhaps it was simply a bad color match from dr colorchip. All of the repairs will look dull as there is no clear on it.

Tried that on my other car. Since it contains no clear coat, the result looked horrible.

It's really hard to capture a small chip about 1.5mmx1.5mm so please bear with me. I would like to know if the chip is into primer at all. If it's not, can I just fill the chip with a clear coat only? Whatever that we see here the color is extremely close to the body color, which is Ibis...

In your opinion, do you think the solution is as effective as before?

Haven't touched the gallon container in months and today I noticed there is a lot of whiteish deposits inside the container. Anyone know what that is?

Not sure, is it supposed to be HydeoFoam in 1:9?

Whats your dilution ratio for HydroFoam in the first bucket? I assume the first bucket is not even half way full otherwise it would be too much predicted being used, right?

Can the CarPro HydroFoam be used with a 2 bucket wash system? I really don't want to grind all of the dirt and debris around the paint while I foam the car and start gliding the wash mitt right away. I was thinking of using Reset in a foam gun. Foam the whole car, and pressure washer/rinse...

UPDATE: Used Griot's G15 and 3 kinds of polish for testing. I found: CarPro Rayon glass polish pad with CarPro glass polish worked the best Also got DP High Perfomance glass restorer and Wolfgang Perfekt vision, which didn't work as well as the CarPro glass polish. The DP polish is very...