Search results

I purchased ONRWW on the 12/12 sale and would like to give it a spin this weekend. So the question is grout sponge or mf towels as the wash media? Is one safer than the other? I've read that the sponge rinses cleaner but with the Garry Dean method using mf towels that wouldn't really matter...

I've seen several people mention that during the winter they will hit the coin op to get the big stuff off of the car and then head home and do ONR In their garage. My question, dumb as it may be, is do you drive the car home wet or are you drying it in some fashion?

I've rinsed this pad out under hot water a few times and worked it from the center out and hit it with dawn power dissovle and let it soak a couple of hours and when it dries it still has these white-ish edges. Is this normal or is there still sealant in it? The pad was used for DG 105/601...

I know you guys clean and seal more than just cars. What do you use to clean and seal ceramic tile and grout in a shower? With our hard water scuzz builds up quickly and I'm thinking if I could seal the tile after cleaning it that it may keep it cleaner longer but perhaps that's wishful...

It's now been 4 hrs since I applied Ironx to my wifes car and followed it with an insane amount of water to flush it out of the trim but it is still bleeding from two spots on the trim. I can't possibly force more water into the area than I already have. Any tips to stop the bleeding?

is it possible to do dg501 on a small cross-over type SUV like a Chevy Equinox with just 1 white pad? I only have 2 white pads to my name and I still need to use one for polishing on my old Maxima so I can't assign both pads permanently to DG 501. I finally have a day off tomorrow and would...

I work by a construction site so by the end of the week my car is covered in a thick layer of fine dust. Its thick enough that when my son touched the car i can see a perfect hand print. Is this too much for a qd? Also I've been working on my car in phases and can see that there is easily twice...

Is it normal to get generate a ton of static while wiping off sealant? Also, I polished my hood last weekend and applied sealant as a last step and it felt really slick. I washed the car today and polished one side of the car and then applied a sealant and noticed that the hood is no longer as...

As the subject says, what is the downside to leaving polishing oils on the car after a polish job? From what I've read the main reason for removing them is to see the actual level of correction accomplished but are there other reasons? Ive completed the horizontal surfaces on my car and used...

I was using UC earlier today with my new gg6 and a LC orange flat pad and ran into some issues. I was never able to get 6-8 section passes out of it without it drying up on me. The most I could do was 4 before I had to stop and wipe the surface down. I was in a garage and the surface was cool...

I'm the kind of guy that if something bad is going to happen, it's gonna happen to me. After reading that some people wear a respirator while using IronX, I'm thinking that's not a bad idea for me. Can anyone point me to a specific respirator that would be good for use with IronX? I started...

I've been looking for a video that talks about this or a how-to article but haven't found it yet. I see a lot of videos of people polishing hoods and other straight-forward areas but do you polish across body panels like say from the door to the fender straight over the gap? How about the fuel...

I'm new to all of this so I'm sorry if this has been asked before. I tried searching and didn't see anything. I'm curious if when using 5.5" pads on a da on the larger surfaces and then using smaller pads by hand on the narrow areas if it's hard to create a similar look between the areas done...

Looking at purchasing the 6 pack of LC 5.5" flat pads (Lake Country 5 1/2 x 7/8 inch Beveled Edge Pads 6 Pack, foam pad kit, build a kit, buffing pads, curved edge pads) for a gg6 and I'm curious which pads I should get for the following products: Ultimate Compound Ultimate Polish DG501 DG105 /...

I have a 96 maxima that has gold lettering and emblems and I'm curious what you would use to clean them up...assuming that's possible. They all have a black coloring to portions of them and I'm not sure if that's gold that's missing or if its accumulated gunk on it. Sent from my Droid using...

I'm considering putting dg 501 on my wife's DD a white Chevy equinox. I've read that 501 really cleans and shines up white well. How many times per year would you re-apply? I've read that it cleans really good so I wasn't sure if I should try to limit the number of applications.

Just found this forum a few days ago and impressed with all of the information here! Can someone tell if if it's possible to buff/polish out the repetitive door ding/scratches shown in the picture? This is my "new" daily driver a 96 Maxima that has about of foot in length of the scratches...