Difference between polish, glaze, wax?? newb needs help

memphisraines26

memphisraines26

New member
Joined
Feb 3, 2009
Messages
42
Reaction score
0
I'm new to the site and trying to start from ground up with detailing. I think I have a good idea of starting with a good wash and technique. Next i want to is do a basic package for a buddy to get started in learning a good start to finish detail.

I've been trying to read through threads and need a lil more info. I keep reading the terms polish, glaze, sealer, and wax. Whats the differences? I think of wax being a sealer. so what is the breakdown of these?

Next when I start on this first vehicle, besides the wash and vac, what should i do next? Clay bar the vehicle? I havent purchased a PC package yet and want to start with cheaper off the shelf products I can pick up at autozone. Once i have a better understanding and technique, i will purchase better quality products. I dont want to overspend and not know what i'm working with etc.

I hope to learn a lot from this forum and got a lot of warm welcomes in the intro forum.

many thanks in advance.:cheers:
 
wash-clay-polish-wax

glaze fills in the fine swirls
polish is small abrasives that break down thus removing swirls
wax is put on last to boost shine and protect paint
sealant is somewhat the same as wax just lasts way longer and usually doesnt shine as much (from what i hear)
 
so would glaze be a temp fix to swirls?
so wash-clay-polish-glaze-wax?
 
yes glaze is only temporary.
and no if you polish correctly you wont need a glaze because the swirls will be gone
 
ok makes sense. so after i good polish and wax, no need to polish again for a long time with proper washing?

i have a couple of 2 gallon buckets to wash with, microfiber mitt, and meguirs wash. what is a good concentration for the wash soap? what temp water to remove salt? i live where the roads are salted bad and heard no hot/warm water to remove that to avoid rusting??

I have the clay bar already.

what should i be looking for off the shelf for basic polish and then wax? should start with low polish and if still there step it up and then reapply with lower cut polish correct?

thanks for all the help. it's getting clearer.
 
with the polish you start with the lightest cut possible. If that doesnt remove the swirls then you move up to a stronger polish. You always want to start light. Im not really sure about the water temp and salt since I live in texas and dont have to deal with that.
 
and you can get some great products from autogeek for the same amount you will pay in the store. Also it will be very very hard and time consuming to polish without a pc.
 
Good user name; with out a buffer you are going to have a very hard time removing any swirls. But if you want to try Megs ScratchX does a o.k job for hand polishing.
 
Noblesville, IN> I was just in your area yesterday. You guys get a little snow down there, and all is in chaos. Plus, no one salts the parking lots or sidewalks.

You need to get some products. Don't waste your money on the off the shelf stuff. I mean, pay the little extra cost and get the right stuff first. Pick up the Menzerna ceramic intro kit, get your PC and it the ground runnin'.

The PC is safe, you won't damage your paint(be smart). YOu don't really need a glaze. Get a good sealant(wolfgang deep gloss 3.0) and a good wax.(dodo, fuzion, souveran and etc)
 
loudog2 said:
Noblesville, IN> I was just in your area yesterday. You guys get a little snow down there, and all is in chaos. Plus, no one salts the parking lots or sidewalks.
Click to expand...

lol i'm from memphis, tn and if you think here is bad about salting and clearing, then go to memphis with just flurries without culmination.

You need to get some products. Don't waste your money on the off the shelf stuff. I mean, pay the little extra cost and get the right stuff first. Pick up the Menzerna ceramic intro kit, get your PC and it the ground runnin'.
Click to expand...

i guess i will look for a good polish and wax. Menzerna i thought was for the hard clear on the new Mercedenz benz and not the older clear coasts like on honda etc

The PC is safe, you won't damage your paint(be smart). YOu don't really need a glaze. Get a good sealant(wolfgang deep gloss 3.0) and a good wax.(dodo, fuzion, souveran and etc)
Click to expand...

i plan on the PC 7424 at the least but thought about doing a couple of test jobs to start with by hand. whats the difference between sealer and wax? i've been told the wolfgang products is good so i guess i'll start with those.
 
Menzerna is used on all cars. SIP/106FA is one of the most popular combos used in detailing. Honda paint is soft, so you won't need to be too aggressive. A sealant last longer than most carnubas. You get that crisp pop from a sealant, and a wet warm glow from a carnuba(not with all).
 
This is from autogeek describing SIP:


"Note: Dark paints may require follow up with a finer polish. Use Menzerna Nano Polish, which is also formulated for scratch-resistant clear coats.

Menzerna Super Intensive Polish can be used on all types of paint, including conventional clear coats. Use it on fresh paint finishes (once fully cured) to eliminate any swirls or overspray. On older paint finishes, Menzerna Super Intensive Polish will remove moderate imperfections and refresh the color."

Same goes for 106FA
 
You must log in or register to reply here.
Back
Top