Rim polishing help.

It's uncoated aluminum.

Sent from my SCH-I545 using AG Online
 
Most professionals use a felt wheel that atttaches to a grinder or a drill for bare aluminum. Flitz sells them here. Make sure you get good metal polish too. If you go this route, buy a small steel brush to clean your wheel when it gets clogged and dirty.
If you use anything other than a soft cone sponge (that attaches to a drill), or a soft felt wheel, you will marr the surface. For example, if you try to use 0000 steel wool, or Nevr-Dull, you will mar the surface. Just make sure whatever your interface is have it be soft.
 
So I should get the power ball or cone? Would that help with this? I didn't want this to happen that's why I went by hand with a Terry cloth. Maybe use a old mf would be better?

Sent from my SCH-I545 using AG Online
 
I do have the flitz polish ball but wanted to go by hand so this wouldn't happen but it did.

Sent from my SCH-I545 using AG Online
 
Try the ball together with a dedicated aluminum polish. You don't want any abrasive in the polish, just cleaners. If you have none, try an AIO, or a cleaner wax on the ball.
 
I thought that might help. I'll try klasse aio tomorrow but what can I do for the one that I did already? Should I go pick up a less aggressive polish? If so what would you recommend? Thanks for your help.

Sent from my SCH-I545 using AG Online
 
808_detail_nut said:
Polishing some welds for my friend and I'm using mothers Meg and aluminum but it has all these small scratches.

I'm going by hand with rather light pressure. Do I need to use the billet polish? What can I do to fix this?
Click to expand...

Heavy pressure. Even hand strokes.
Billet polishes are fine, to ultra-fine cut. Not intended for moderate defects. Probably won't suffice. Mothers Mag and aluminum polish is a great product, but probably will only correct fine to moderate scratches and swirls.

Linking a helpful post.

The Guz said:
Meguiar's offers some various metal polishes. They have heavy, medium and finishing. You may want to check them out.

Here's a couple threads if you want to read up on them.

Our new Metal Polishes put to the test

Metal Polishes
Click to expand...
 
Thanks for that, been looking at trying out the megs metal polishes. I'm thinking I need the medium and the finishing maybe to help fix the marring. Hope I can find it someplace localy.

Sent from my SCH-I545 using AG Online
 
808_detail_nut said:
Thanks for that, been looking at trying out the megs metal polishes. I'm thinking I need the medium and the finishing maybe to help fix the marring. Hope I can find it someplace localy.

Sent from my SCH-I545 using AG Online
Click to expand...

My biggest gripe about the megs product is the quantity/price. Bummer.

If you cut by hand, you'll probably cut each wheel twice, or cut a section, see progress and recut that section again before continuing on to the next section. Either way you'll use up a lot of product.

If I were doing those wheels by hand, I'd allow myself four hours per wheel.

However, if you under promise, and over deliver, you can correct to the 85% range or better, resulting is some serious bling, and off the hook coloring.

Don't forget to seal your work with a long lasting product such as Collinite 845.
 
I'm not sure but I'm gonna hit the rims today with (i hope wally world has it) megs medium cut then fine then klasse s/g.

Sent from my SCH-I545 using AG Online
 
KB in MD said:
Could terry cloth be to course of a material?
Click to expand...

No.

I prefer using only 100% cotton towels for aluminum.
I will cut up a bath towel because I don't like the size or lack of plushness from generic 100% cotton shop towels.
On occasion I'll waste a Dollar Store/Walmart mf towel while cutting.

I never use mf on finishing or lsp steps on Al. But that's me.
 
Well I definitely need some work on polishing alloys. Tried everything I could find on it, even rouge and nothing finished without some scratches. Very disappointed. I was so upset I didn't even take any more pictures. Of course I returned it to my friend and he was happy and didn't even notice. Thinking of buying the zeypher kit and trying it out. Anyone use their system?

Sent from my SCH-I545 using AG Online
 
I used to use Eastwood's felt polishing cones and their polishing sticks including red rouge, chucked to an hand held air grinder and had great success on uncoated aluminum wheels... They make a nice thick pointed one out of felt or some type of cloth that rocks in the machine..

Everything turns black because its uncoated aluminum, so you need to wear gloves and try not to inhale all the stuff coming off..

If you are still doing these by hand well, that is probably not working very well - especially if the defects are a little deep..

You need a machine to do any uncoated alloy wheels, in my experience..

Coated with clearcoat wheels just need an appropriate compound or polish that you would use on paintwork..

Sorry this had to happen to you !
Dan F
 
I'll look into it, thanks. I was using my plug in drill with polishing wheels I bought locally. He said he would let me retry later on when it gets bad again.
 
Why buy a kit if youre not gonna use it often. With the kit you will need at minimum six to eight cutting and polishing wheels.
Some where between a buck and one fitty to start...including your arbor, rake, etc.
There was no way you could have corrected to near pristine without a laborous multistep and multiprocess attack.
You said he was happy...so be it.
Im looking into the new Flex lightweight because of size and higher rpm range...perfect for what im working on lately.
 
I have the 3403 and it's a awesome machine. I don't think I am going to buy it. My drill I think will work fine. Thanks for you guys help. I appreciate it.
 
You need to use a sisal wheel and tripoli compound to remove defects. If you want after use Mother's Billet Polish for extra shine.
 
You must log in or register to reply here.
Back
Top