What to swap m105 with?

[Bill1234]

Ive been using m105 for a while now. Ive used it on some GM hard paint, Ford paint, Audi,Jeep I think and others. It has the cut but dries out too much and dusts alot. Is there anything I could swap it with that works just as well?

 

[Klasse Act]

Try M101

Sent from my SM-G950U using Tapatalk

 

[Bill1234]

bit expensive at 60 bucks for a 32 oz

 

[Klasse Act]

bit expensive at 60 bucks for a 32 oz

Quality doesn't cost, it pays

Sent from my SM-G950U using Tapatalk

 

[PaulMys]

Try Griot's Fast Correcting Cream.

You will not be disappointed. :xyxthumbs:

 

[Mike lambert]

Griot’s fast correction cream, just works! No dust, no water spray and you can get an LSP ready finish.

 

[The Guz]

You are going to get a lot of recommendations.

Meguiar’s just released their new M110 compound. This may be a good alternative if you want to stay with a SMAT compound.

Sonax Cut Max is great. Diminishing abrasive unlike M105 but leaves a better finish and no dusting.

Meguiar’s D300 with their microfiber cutting pad is another good one.

Try M101

Sent from my SM-G950U using Tapatalk

Get it while you can. Meguiar’s has mentioned that they are going to phase it out now that they have their new M110.

 

[tcope]

I'd highly recommend Ultimate Compound. It is 1 under M105 on the aggressive scale. I had the same problem with M105... it just dusts _really_ bad. I've never had this problem with UC.

I'd say that you might need to work UC a little longer than M105 but, as mentioned above, this is fine as it does not dust.

 

[DMW]

I switched from M105 to Menzerna FG400 and never looked back.

 

[Klasse Act]

May I suggest the brand new 303 compound, used it, low dust, GREAT product

Sent from my SM-G950U using Tapatalk

 

[Dr Oldz]

So many good ones

Sonax CutMax is my favorite.
Jescar Compound
Griots FCC
CarPro Clearcut

 

[rlmccarty2000]

Meguires d300 and Menzerma FG 400 are my go to compounds.

 

[dlc95]

I'm really, really digging 3D One.

The lubricant is butter smooth and feels great under the buffer. Minimal product needed. Excellent cutting, even with a foam pad (green Buff and Shine for me). Finishes very nice for the cut it delivers. Little to no dust.

One also makes a great finishing polish simply by changing the pad. I like the blue Buff and Shine.

Meguiars Ultimate Compound, M100, and Menzerna FG400 have been my go-to compounds for the past few years.

 

[Dan Tran]

So many good ones

Sonax CutMax is my favorite.
Jescar Compound
Griots FCC
CarPro Clearcut

The fact that I am stunned by CarPro ClearCut for a compound (and though not talking specifically about polishes) Sonax Perfect Finish means that I MUST add Sonax Cutmax to the list.

There was a thread I posted a while back asking if Sonax is a good brand. I’m FULLY convinced that they are worth every penny since using Perfect Finish and their glass cleaner.

I can’t imagine what Cutmax is capable of doing...

 

[TTQ B4U]

CarPro Clear Cut.

Sent from my Galaxy Note 8 using Tapatalk

 

[Eldorado2k]

Ive been using m105 for a while now. Ive used it on some GM hard paint, Ford paint, Audi,Jeep I think and others. It has the cut but dries out too much and dusts alot. Is there anything I could swap it with that works just as well?

Try Meguiars new M110.