A polish like HD Speed?

AZpolisher15

New member
Joined
Nov 9, 2015
Messages
1,419
Reaction score
0
Hey, Crew. So, I've been reading all kinds of praises for HD Speed. Could you recommend a product to me that will correct/finish similarly to HD Speed but DOES NOT contain a sealer component?

Would this be something like Menz PF2500?
Or Ultimate Polish?
HD Adapt?
Or???

What would be a somewhat accurate comparison?
 
Griots BOSS Correcting Cream
HD adapt
Pf2500

Correcting cream is one of the best one step polishes out.

It cuts awesome and finishes LSP ready, it works forever , no dusting, easy wipe off, a dream to work with.
 
I need to start sampling the GG BOSS polishes. I don't think that I've seen anyone have negative comments about them yet.
 
I found Correcting Cream to have alittle less cut than Menzerna PF2500, it did spread a really long ways and had a pleasant orange scent but 2500 edges it in cut.
 
Hey, Crew. So, I've been reading all kinds of praises for HD Speed. Could you recommend a product to me that will correct/finish similarly to HD Speed but DOES NOT contain a sealer component?

HDPolish

HDCut is there too but you mentioned Speed so I went polish vs compound level correction.
 
Boss correcting cream. I also just had the pleasure of receiving Polish Angel Master compound and Master polish. Both are unbelievable products but are a bit pricey. Master compound works so nice.
 
What about the new McKee's 37 360?? I haven't had a chance to try it out yet but it appears to be very similar to HD Speed.

Disregard...I just-reread and you are looking for something without the sealant component.
 
What about the new McKee's 37 360?? I haven't had a chance to try it out yet but it appears to be very similar to HD Speed.

Disregard...I just-reread and you are looking for something without the sealant component.

What about McKees 37 Fast Polish?

I too have read so many great things about HD Speed but I'm concerned with its sealant characteristic affecting the adherence of McKees 37 Paint Coating. I assume one would need to wipe the surface prior to the coating application with something to remove it which is an extra step. A step I'd prefer to avoid.
 
Thanks a bunch to all of you for the suggestions. I'll do some reading on those you mentioned. I'm working with a GG6 and am very limited on time these days. I really like my Menz Powerlock Sealant- just looking for a good one step product to go with it. I really don't want to go to the compound level. Not chasing all the scratches. Just wanna clean up some and seal with the PL.
 
HD Polish? It is the exact same thing as Speed without the Poxy sealant Speed has.
 
HD Polish? It is the exact same thing as Speed without the Poxy sealant Speed has.

That is not accurate, spoke with David from 3d he was not going to say the exact formulation for obvious reason , but speed has a mix of cut, adapt,and polish and poxy all in one. Speed cuts better then HD Polish
 
Thanks a bunch to all of you for the suggestions. I'll do some reading on those you mentioned. I'm working with a GG6 and am very limited on time these days. I really like my Menz Powerlock Sealant- just looking for a good one step product to go with it. I really don't want to go to the compound level. Not chasing all the scratches. Just wanna clean up some and seal with the PL.

Menzerna 2500 or 3 in 1.
 
That is not accurate, spoke with David from 3d he was not going to say the exact formulation for obvious reason , but speed has a mix of cut, adapt,and polish and poxy all in one. Speed cuts better then HD Polish

Not doubting you, but I asked a 3d rep on autopia and he said Polish would cut better than speed.
 
Not doubting you, but I asked a 3d rep on autopia and he said Polish would cut better than speed.

I've seen the same posted as well....HD Polish+ smells like Adapt now too so who knows.
 
That is not accurate, spoke with David from 3d he was not going to say the exact formulation for obvious reason , but speed has a mix of cut, adapt,and polish and poxy all in one. Speed cuts better then HD Polish

I have probably used a gallon or more of both speed and polish, polish cuts better. Adapt and Cut were not even out when Speed was released, and to my knowledge the formulation has not changed.
 
I have probably used a gallon or more of both speed and polish, polish cuts better. Adapt and Cut were not even out when Speed was released, and to my knowledge the formulation has not changed.

This is what David from 3d told me at Detail Fest.

Alot of people have mixed responses now, i would certainly love to know, guys from 3d on this forum have said it is not just Polish and Poxy as well, guys above are saying thats what they said on autopia, so definitely interesting
 
Back
Top