Quik question about Mckee's Paint Coating

Eldorado2k

Eldorado2k

Well-known member
Joined
Nov 9, 2015
Messages
14,566
Reaction score
693
Is a 24hr. curing time absolutely necessary? What about morning dew? Is it critical to avoid morning dew as well?


Sent from my iPhone
 
You'll be fine. I've let mine cure for 5 or so hours and had it get wet with no issues.
 
pdqgp said:
You'll be fine. I've let mine cure for 5 or so hours and had it get wet with no issues.
Click to expand...

Ok cool. I want to try it out on a panel on my car, but it's already 4pm. and the dew will be here tonight and I wasn't sure. I'm gonna clay, machine polish with Griots Perfecting Cream, IPA, then coat.


Sent from my iPhone
 
Eldorado2k said:
Ok cool. I want to try it out on a panel on my car, but it's already 4pm. and the dew will be here tonight and I wasn't sure. I'm gonna clay, machine polish with Griots Perfecting Cream, IPA, then coat.
Click to expand...

Gotcha. You'll like it. I usually do two coats to insure full coverage.

It's been holding up extremely well on my wife's van.

Here it is after a week of driving in the rain and fall muck as it sat in our driveway being rained on. Snapped these before I left the other day. Not bad for a dirty car.





 
Nice beading... Better yet, I'm gonna use Essence, then coat.


Sent from my iPhone
 
Eldorado2k said:
Nice beading... Better yet, I'm gonna use Essence, then coat.
Click to expand...

There you go. I did that on my S4 but the not yet on the van. I'll wait to hit the van with Essence and re coat it in the spring. The only thing left to do on the van is clean it up for winter and for the sake of it, top it with Essence Plus, necessary or not. It will fulfill my OCD Needs.

Essence and McKee's Paint Coating are my go-to for many of my details.
 
Ok, so I applied Mckee's paint coating to the left side of my hood.

0ecdbd7e359071d10bbe142f400c346f.jpg


And the sealant of my choice [which shall remain nameless] on the right.

b62024b468efe7b0b973a379dfed9e1e.jpg


It applied easy enough, no problems. I'll remove the tapeline tomorrow morning to avoid any possible dusting from it. I also applied the paint coating across all my trunklid.


Sent from my iPhone
 
It's just after 2pm. and as expected the rain started coming down a half hour ago...

Mckee's Paint Coating⬅️
➡️Sealant

e876f9fc853c470f7d9d1dfe88c8c4bf.jpg


b6b246737540b79f64e5986ce35a4aab.jpg


Mckee's Paint Coating on the entire trunklid.

001a74aee6d74b003bcfcdf6bd3e28ff.jpg



Sent from my iPhone
 
I applied a second coat after 12 hours without any problems.
 
Vegas1 said:
I applied a second coat after 12 hours without any problems.
Click to expand...

Not that I was really think about it, but what does the manufacturer recommend as far as a 2nd coat?


Sent from my iPhone
 
The driver's side of the hood has a more visually consistent beading pattern. The McKee's coating side kind of looks like a sealant that is a bit older and is showing sign of performance degradation.

How long did the coating cure prior to coming into contact with moisture?
 
osiapstndp said:
The driver's side of the hood has a more visually consistent beading pattern. The McKee's coating side kind of looks like a sealant that is a bit older and is showing sign of performance degradation.

How long did the coating cure prior to coming into contact with moisture?
Click to expand...

3+ hrs. before a light layer of condensation from the cold began to form. When I last checked it last night it was only a small patch in the dead center of the hood, both sides were equally matched with the dew. The trunk had a light even layer of condensation at about the same 3hr. mark.

We had an overnight low of 50 degrees last night.

As far as this actual rain that's going on right now, 19hrs. from the point it was applied to the time it began raining at 2pm today.


Sent from my iPhone
 
It's still raining at the moment. I went outside and took these pictures just now.

97611cee55db69aec65dfae370e1ed59.jpg


cfc7efe0d691d10d2e63264028e0041c.jpg


Drivers side [sealant]

e6c260dd96688c3f52ad05a2fcf47629.jpg


Passenger side [coating]

6013d74ba85bfffd41de9aabf1f677af.jpg


Trunk [coating]

bbde57082e560209d95814e254b8d29d.jpg


FYI: The car hasn't moved the whole time.



Sent from my iPhone
 
If you don't mind me asking, what was the prep prior to applying both the coating and sealant
 
jkrig said:
If you don't mind me asking, what was the prep prior to applying both the coating and sealant
Click to expand...

Waterless wash with Wolfgang Uber, then Meguiars white consumer claybar with Megs D114 as claylube, Carpro Essence w/Orange LC HD Orbital Foam Polishing Pad on Boss G21. Tape down the middle, Coating was applied 1st while the right side of the hood was covered with a waffle weave. Sealant applied 2nd. I used 2 Brand new foam applicators [and of course 2 separate clean microfibers for each]
 
Did you allow any wait time to apply the coating over essence? I've seen Cory of car pro recommend waiting 1 hour before applying a coating. Or wiping it with an IPA equivalent prior to applying the coating.

The beading looks like when a car is parked under a tree.
 
The Guz said:
Did you allow any wait time to apply the coating over essence? I've seen Cory of car pro recommend waiting 1 hour before applying a coating. Or wiping it with an IPA equivalent prior to applying the coating.

The beading looks like when a car is parked under a tree.
Click to expand...

Certainly not an hour, no.
I would've never thought anything like that based on the little I had heard going into it... What's an hour going to do? Besides make cold beer warm? Lol. J/k... But at 1st thought, why would that really matter?


Sent from my iPhone
 
Especially after all the stuff I'd heard about Essence being such an "ideal" step before coatings.... Ugh now I'm actually a bit bothered... grrr. I Never heard anything about having to wait an hour. What's up with Carpro not getting their message across in proper manner? How many times has this happened? Smh.


Sent from my iPhone
 
The Guz said:
Here you go

65A025D8-3CAE-422B-B668-497AE14FBB04_zpsfu5rdvz2.png
Click to expand...

Where's that from? Facebook or something? That's neat, however I'm not on Facebook, I've never even clicked on that site, ever.

I won't hold them accountable for this because they have no responsibility to how Mckee's Paint Coating cooperates with Essence, but I still don't understand how hard it is for that company to put out "official word" on a professional level... Maybe it's just me, but I would think 1st priority would be to get your description thoroughly explained across the board on every website where your product is sold in order to at the very least avoid dozens [if not hundreds] of customers calling your customer service line with needless questions everyday... IMO this type of stuff should be automatic, not a "problem" I should be asking about.

Put it in the description everywhere your "pro" product is sold. These are very simple protocols.

Rant over.


Sent from my iPhone
 
You must log in or register to reply here.
Back
Top