White 'haze' on my car

N

newb001

New member
Joined
Aug 30, 2010
Messages
356
Reaction score
0
I'm guessing it's road salt, but is there anything else that could be causing the white haze on the mid-to-lower half of my black car? Haven't done any detailing over the winter, just a couple of trips through the touchless to try and remove the salt/etc. before it sets in...

Tried cleaning with ONR today, but it would not remove the haze. Even scrubbing really hard in a low, inconspicuous spot wouldn't remove the haze at all. The only thing that removed it was rubbing my finger against it. I'm guessing maybe clay would work but not sure.

Any thoughts as to what it is/what I can do about it?

Thanks!
 
Sometimes it takes a good old
fashioned hand car-washing
session (using *agitation*) to
remove stubborn road film/salt
and other stuck-on contaminates.

Your below "contaminate removal process"
surely points out *agitation* as being a key
element for your white 'haze' removal.


Bob

newb001 said:
I'm guessing it's road salt...

Haven't done any detailing over the winter,
just a couple of trips through the touchless
to try and remove the salt/etc. before it sets in...

The only thing that removed it
was rubbing my finger against it.
Click to expand...
 
I'll post pics tomorrow (my phone was left inside earlier).

Even using the ONR soaked MF and agitating basically as hard as I could, nothing happened. Only my finger worked for some reason.
 
Here's what I mean.

I tried again today with a waterless wash, and really scrubbed hard an inconspicuous spot and it did nothing.

I tried claying as well which worked a little, but not perfect.

View attachment 55115
 
newb001 said:
Here's what I mean.

I tried again today with a waterless wash, and really scrubbed hard an inconspicuous spot and it did nothing.

I tried claying as well which worked a little, but not perfect.

IMG_2308.JPG
Click to expand...
Instead of salt/salt stains, that looks
more like stains caused from the trips
through the touchless and the harsh
chemicals they make available for use.
(It even appears they're in/under the CC.)

Try a test spot using a mild polish/AIO...
without too much pressure...and see what
results you get. Being too aggressive can
result in breaching the CC.

Good Luck!


Bob
 
Ugh. Thanks for the info (though of course not what I was hoping to hear). I do have some Klasse AIO so I'll give that a try. I hope/assume it'll work, given that my my finger is able to rub off this 'gunk'.
 
Hello,
If your fingers are able to rub it off, then I would say a paint correction should remove this for you.

Since I don't know what tools and products you have I would start with the least aggressive product you have in your arsenal and work your way backwards until you find what works.
 
Also, if it is a stain, would something like Optimum Power Clean possibly work? Or should I stick with an AIO b/c it probably needs the polishing effect?

I don't want to try OPC without being able to properly wash it off, and I can't do that unless I go and turn my hoses on again. Which I could do as it's very warm this week, but generally prefer to wait until spring arrives...
 
Killerheroin said:
Hello,
If your fingers are able to rub it off, then I would say a paint correction should remove this for you.

Since I don't know what tools and products you have I would start with the least aggressive product you have in your arsenal and work your way backwards until you find what works.
Click to expand...

I don't have much in my arsenal (and no equipment to do any 'real' work). An AIO by hand is the most aggressive I can do. Other than that, Power Clean is the next most aggressive.
 
I am surprised a good hand wash would not take car of this. I don't use waterless, so not sure the "cleaning power" of it, but I would think a good mitt, maybe a slightly heavier dilution ratio of a reputable wash soap and some good old fashioned elbow grease would remove the majority of that.

It doesn't shock me clay didn't touch it. IME clay is fantastic for particles that are imbedded and "stick out" from the paint, but not so much for stains that have become "part" of the paint.

I would take a crack at it with a two bucket method and some good soap. Just make sure your mitt is SUPER clean and rinse it often or your stains may disappear, only to be replaced with severe swirling and marring.
 
A regular 2 bucket wash and KAIO seemed to do the trick!

Thanks everybody.
 
You must log in or register to reply here.
Back
Top