Recent content by agon

I did try the spray bottle method with the Klasse. Great suggestion. It was much easier to apply that way but I still had a bit of residue left over. Maybe I'll try the wolfgang next time.

Not to derail this thread, but I just finished putting Klasse HG Sealant on my vehicle. How does Wolfgang's sealant compare to that application wise? I like what the Klasse did but it was such a huge pain to get it to apply easily, especially on areas like the hood and larger panels. So next...

I'll see what it looks like tonight, and if it still has that residue look after I use IPA on it, I'll wash it. Thanks for the suggestion.

I do model my technique after your video. But since it is fall here and the humidity is low the product tends to dry a bit on the edges of the pad so I still see the film on the surface of the vehicle, and when I'm finished working the product the film is still slightly damp. If I run my...

Yeah, I usually work the 205 until I can barely tell it's on there, usually it starts dusting a little bit before I finish working it. Last night I reworked the hood with 205 and the white pad making sure that I cleaned well after every pass. I'm pretty certain I was able to remove all of the...

I just did my first application of KSG last night and had the exact same problem. Tonight I'm going to try this technique instead. Sounds like it should make things much simpler and my arm won't fall off. I do have one other question. Right now I'm able to leave the vehicle in a garage between...

I cleaned the section I taped off tonight with some denatured alcohol and checked it under my halogens and I could see some light trailing on there so I hit it with M205 on a black pad at a higher speed than I had been running before and it appears to have taken the holograms out. Though I'll...

Thanks for the tip, I didn't even think of trying to remove them by hand first. I don't think they're RIDS they're just about gone and they don't catch on a fingernail at all. I'll give the hand working a shot and then follow up with a pass of the orange pad and see how it goes. If they can't...

Ok, should I be cleaning the surface with that after the pass with the 105? I've got some denatured alcohol that I could use to clean it up. You're thinking it might be some residual 105 on there marking it up during the pass with the 205?

That is correct. I do have both a yellow 5.6" flat pad and a wool pad I can try. I'll give them a shot on the section. Just seems strange to me that all of the swirls came out no problem but the water blade marring, which were finer scratches to start with, and appeared to be shallower, are...

I've been doing what was described on the bottle. I usually do 3 section passes with moderate pressure, I'd say 10 - 15lbs or so, and then 2 passes with light pressure so the pad spins a bit faster, say just a bit more than the weight of the PC. As far as between applications of 105 and 205...

Actually the only place on the vehicle that has this issue is the hood. The rest of the vehicle is looking very nice. I just can't get rid of the fine scratches on the hood there. Hopefully the new video I put up shows it a bit better. It's a VW Touareg if that helps. It seems to have a pretty...

I tried a pass with the White pad and M205 and it didn't do anything. So then I hit it with an Orange pad and M105 followed by the white with M205 and the result showed almost no change. Here's another video I took after trying a section out. The section on the left side of the tape is the one...

Yeah, I guess it is difficult to see in the video. It's visible when the sun glares off of the finish. I'll give the white pad a shot and if I still can't get it out I'll try another video. I don't think the marring is very deep so hopefully the white pad does it.

I've recently been working on my second paint correction job with my PC 7424 xp. The first one came out excellent using just an orange pad and Meguiars Ultimate compound. And I've worked my way around the vehicle and have done a full work down on the hood, but I can't seem to remove some slight...