Search results

Lost one of my babies today.

Coatings I have used started with Blackfire Crystal coat which I did two with. Then just Essence topped with Reload when it was very 1st released for my car's 1st. I have also used WG Uber, my favorite to apply CSL, also CSL topped with EXOv3 and EXOv4, Gyeon Syncro, MOHS+Booster, and now Miyabi...

Last Thurs I started with a full decon wash with 3D Super Pre-Soak, McKee's 37 Xtreme Iron Remover, McKee's 37 Coating Prep Auto Wash. and Iron X Snow Soap. Today I finally started to polish off the existing coating in preparation of a new coating. I figure it will take me a week or more since...

If I were you I would do the decon wash but forget about the clay to not chance marring the paint. I would then coat it with can coat and apply that like every spring and fall. I would not try to do CSL on CSL without removing the coating 1st. Can Coat is quite hydrophobic and would to me be a...

It's a Hyperikon LED Flood Light,100w that was a gold box deal on amazon, I could only get one on sale so got my brother to order the 2nd. All the main lights are Hyperikon LED.

Sounds quite similar to my setup except for a single car garage. I have 4 72 watt 5k 7100 lumen lights on the side walls and 1 100 watt led 10,000 lumen on each end along with 2 100 watt equivalent 5k led's in my garage door opener. Also not shown is a standard led shop light over the bench but...

For the 1st step I used Meguiars DA Microfiber Cutting Discs, compounding discs, cutting pads with FG400 and for the final step I used 5.5 Inch ThinPro White Polishing Pad (Single) with mostly menz 4000 even tho I did do parts with 3800.

Here is the link but will have to copy and paste and hope it works. Wash - Ancient_1 Here is a copy of the photo on a different hosting site.

I have a few pictures of my car from last year when I did a RW/WW on it when I had CSL with EXO v3 at 9 months. It was quite cold then too and it hit a high of 2f that day. I first sprayed it down twice with N914 at WW strength and then did a RW with N914 at RW concentration. We can have some...

With CSL being a apply and wipe off with no wait for flash I would guess humidity would have very little to do with it either. I have done about 10 vehicles with CSL in the last year or two with quite different conditions and it always seemed to act the same. I will say EXO was different...

Temp would have very little to do with CSL since it can be applied in temps as low as 5c.

Yesterday I was finally able to do a decent cleaning of my garage floor. Finally no snow and it got above freezing. Just to see how bad it was getting here is a picture of when I did a RW of my car and since then it just got worse. And one when done Depending on weather I plan on...

Here is one from about an hour ago after a $4.80 touchless wash on the way home from HD.

This was last week bnut never got a chance to post it even tho it was the same yesterday but never got a picture.

I don't have the actual before pics but the 1st is after I leaned with tire cleaner and then a second time with goof off. The next is a picture of the tool I used to get it pretty much completely clean and a shot of the result. If it woked on road paint that had been on for over six months I am...

Here is what it says now and to think rain is forecast for this weekend.

Our next 5 day outlook

I use an adjustable 30~50k for my single car garage and it works fine at the lowest setting, just need to set on high to melt the fenderwells behind the tires. 1st pic is of the heater in operation and the second is a picture of the indoor/outdoor thermometer showing ho cold it was outside that...

Well I will try again. I haven't posted a picture this year before and didn't realize that Photobucket wasn't showing up anymore.

Syncro at just under 9 months.