megs BP

jamores23

jamores23

New member
Joined
Dec 17, 2008
Messages
974
Reaction score
0
Im looking for a backing plate for my MF pads. I currently have the one that came with it w67da but i believe I got a defective one. NONE of my pads stick to it and no , its not melted. I got the 5.5 in pads so i need the 5 in bp . I cant seem to find the bp by itself on ag. Any one had this problem as well? my pads have gone to crap on the velcro side as well cause of this. I will be ordering new pads and a new bp, if this happens again im done with the mf system. should i go with the w67 bp again or get another bp?
 
If the BP is defective, they'll replace it. Contact the place where you bought it.
 
I think yours is fine..I bought one to and that plate sucks..it doesnt hold crap..it holds the MF pads better cause they have a longer fibers on back but foam pads hardly even stick to it..I basically tossed mine out as it was junk after using it once and watching it chew the edge of my HT pad off. since the pad kept slipping around in it..its not worth the money. I just use my Lake Country and never have any issues.
 
05xrunner said:
I think yours is fine..I bought one to and that plate sucks..it doesnt hold crap..it holds the MF pads better cause they have a longer fibers on back but foam pads hardly even stick to it..I basically tossed mine out as it was junk after using it once and watching it chew the edge of my HT pad off. since the pad kept slipping around in it..its not worth the money. I just use my Lake Country and never have any issues.
Click to expand...

I think you guys both may have defective ones... or it's mutual operator error. I've got a W67DA plate that I've been using for quite a while with several different types/brands of pads and it has never had a problem like either of you describe.
 
i dont know how you can have operator issue..take pad..stick it on plate done..The Megs plate has almost no grip I was cleaning my one pad on the fly once and it almost flew off cause the hook and loop is to short on that. I personally dont like it at all
 
hmmm,

I wonder if the optimum pads will work fine on an LC bp?

I read that they were a bit smaller than the Megs pads
 
jamores23 said:
Im looking for a backing plate for my MF pads. I currently have the one that came with it w67da but i believe I got a defective one. NONE of my pads stick to it and no , its not melted. I got the 5.5 in pads so i need the 5 in bp . I cant seem to find the bp by itself on ag. Any one had this problem as well? my pads have gone to crap on the velcro side as well cause of this. I will be ordering new pads and a new bp, if this happens again im done with the mf system. should i go with the w67 bp again or get another bp?
Click to expand...
When I bought the MF system it can with the BP I bought the 5'" system it came with the compound and wax . Did you buy everything separate ? I used it all today and had no issue at all with the pads or the BP .
 
i have never had any problems with the MF pads as they have a longer strands on the backing..its foam pads that have issues for me with staying properly attached
 
yes adam i bought the whole kit, ive gone through 3 cutting pads 5 in now on the smaller pads the 3 in, i got the unigrit bp and it is almost impossible to take of the pads when on the other hand the 5 in combo you could blow on the pad and it will come off.. megs says there bp is made for the mf system, so would getting a lc 5 in bp take away the ability of the mf pads? i think its all the same right?
 
jamores23 said:
yes adam i bought the whole kit, ive gone through 3 cutting pads 5 in now on the smaller pads the 3 in, i got the unigrit bp and it is almost impossible to take of the pads when on the other hand the 5 in combo you could blow on the pad and it will come off.. megs says there bp is made for the mf system, so would getting a lc 5 in bp take away the ability of the mf pads? i think its all the same right?
Click to expand...
When I get into work tomorrow I will check and see how well the LC backing plates hold the MF pads I would do it now but I have everything at work I've been working on some cars . I have no problems at all with the backing plate that came in the kit matter of fact I really have to give a good pull to get the pads off of it .
 
Harleyguy said:
I have no problems at all with the backing plate that came in the kit matter of fact I really have to give a good pull to get the pads off of it .
Click to expand...

I am using a W67DA and that is my experience as well. I was afraid I was going to tear the MF pad apart pulling it off.
 
yeah, so I guess im just going to get a lc bp 5 in.
 
is there any difference between the w67da or a lc 5 in bp?
 
jamores23 said:
is there any difference between the w67da or a lc 5 in bp?
Click to expand...

LC on left, W67DA on right:

BPs.jpg


Velcro.jpg


LC:

LCVelcro.jpg


W67DA:

MGVelcro.jpg


The W67DA's loops are DEEPER than the LC plate -- they actually hold *better* than the LC plate.
 
i ordered the lc pad to try it out, but my w67 sucks...
 
You must log in or register to reply here.
Back
Top