Hey all, I used griot's garage one step sealant on a orange gg pad last weekend. While it did reduce swirls a lot on my 2011 WRX, it didn't quite get them all. My question is what should be my next step? A more aggressive pad or a more aggressive wax/abrasive?
More aggressive cutting needed, next step?
- Thread starter RedMed
- Start date
Mike Phillips
Active member
- Dec 5, 2022
- 51,004
- 7
I'd get a dedicated polish or compound instead of trying to do the job with a cleaner/sealant. (cleaner/wax)
When the word dedicated is used to describe a paint care product it means the product is for most part designed and formulated to do a very specific task, like a polish is for removing swirls... not removing swirls and leaving behind a coat of protection.
When the word dedicated is used to describe a paint care product it means the product is for most part designed and formulated to do a very specific task, like a polish is for removing swirls... not removing swirls and leaving behind a coat of protection.
Mike@DedicatedPerfection
New member
- Feb 26, 2011
- 12,365
- 0
As Mike said, a dedicated polish will be needed to remove the swirling seen in your paint.
A good polish on a white pad would be a good starting point to see if that removes the swirls. If not you can step it up from there. After that seal it with a quality Sealant.
A good polish on a white pad would be a good starting point to see if that removes the swirls. If not you can step it up from there. After that seal it with a quality Sealant.
- Thread starter
- #4
I'd get a dedicated polish or compound instead of trying to do the job with a cleaner/sealant. (cleaner/wax)
When the word dedicated is used to describe a paint care product it means the product is for most part designed and formulated to do a very specific task, like a polish is for removing swirls... not removing swirls and leaving behind a coat of protection.
Alright, I have megs fine cut cleaner handy. Would that do the job?
allenk4
In time out
- Mar 12, 2013
- 4,845
- 0
Depends on the defects you are trying to correct
Post some pictures and you will get more accurate suggestions
- Thread starter
- #7
Will do, as soon as I can.
Paul A.
New member
- Dec 21, 2007
- 5,276
- 1
If i understand your original question it seems you're asking...
After seeing a particular pad/product combo remove some of the defects, what should you up next to get the remaining results i.e. should you up the pad and use the same product or up the product and use the same pad? That's been a common question and i've done both sometimes and done neither other times.
If i am doing a test panel and i see there is very little affect i grab a tougher cut product but try it on the same pad...maybe white pad. Basically i usually change my cut product first and then change to a more aggressive pad last. If my test panel yields about a 60-70% improvement i just do it again with the same combo.
After seeing a particular pad/product combo remove some of the defects, what should you up next to get the remaining results i.e. should you up the pad and use the same product or up the product and use the same pad? That's been a common question and i've done both sometimes and done neither other times.
If i am doing a test panel and i see there is very little affect i grab a tougher cut product but try it on the same pad...maybe white pad. Basically i usually change my cut product first and then change to a more aggressive pad last. If my test panel yields about a 60-70% improvement i just do it again with the same combo.
JHL88
New member
- Mar 17, 2013
- 1,137
- 0
DogRescuer
New member
- Apr 6, 2013
- 1,801
- 0
Menz400 any day.
- Thread starter
- #11
Thanks! That's the answer I was looking for
Paul A.
New member
- Dec 21, 2007
- 5,276
- 1
And now thinking more about it i do a lot of different things but usually "feel" what i should try next. That's easy to say here but it depends on what i'm working on specifically. There have been times i just go from a white pad to an orange pad with the same product, maybe exert a little more pressure on the machine and other times i stick with the same pad and try a slightly more aggressive product and...bam...there's what will work. After doing literally hundreds of test sections you kinda get a feel for what might work in those conditions but it's always a guess for the least aggressive method first and go up from there.
One of the common themes with correction is either time or impatience. Some folks want those swirls GONE and FAST! Don't be hasty and find a technique that removes just enough paint to level it...not more than you need to. You'll find over time how to maybe tweak whatever you're correcting. And maybe it's just machine speed! (not arm speed, i mean cranking the dial up).
I find test panels some of the most rewarding practices in the whole game. Finding what might work best for THAT paint. And that's just the heavier correction test. Dessert for me in that meal is finding the perfect finish step! :dblthumb2:
One of the common themes with correction is either time or impatience. Some folks want those swirls GONE and FAST! Don't be hasty and find a technique that removes just enough paint to level it...not more than you need to. You'll find over time how to maybe tweak whatever you're correcting. And maybe it's just machine speed! (not arm speed, i mean cranking the dial up).
I find test panels some of the most rewarding practices in the whole game. Finding what might work best for THAT paint. And that's just the heavier correction test. Dessert for me in that meal is finding the perfect finish step! :dblthumb2: