Turtle Wax Seal and Shine

Coatingsarecrack said:
I found SNS REALLY hard to remove. 4 sprays on Autofiber applicator and covered half the hood. Wiped with 365 gsm TRC. Buffed with 800gsm Everest.
Click to expand...

Perhaps humidity related? I've found it very easy. Spray, wipe, buff. When done with the entire car, I go back over and remove any streaks with a damp MF Rag with nothing but distilled water on it. Perfect shine and super slick. Based on this ease of use and longevity related abuse I've seen it being put through and surviving online, it's now my go-to top layer for basic Polish and Protects and over top of my AIO's I use.
 
FUNX650 said:
Just curious:
All these “issues”—yet adhering
to the product’s instructions?

:confused:


Bob
Click to expand...

Not issues.... issue

I applied to applicator wiped on wiped off..... unless it is different than the vast majority of sealants out their....

Maybe 4 sprays to much but I have not had problems removing ANY other product I applied.

Feels “greasy”


Sent from my iPhone using Tapatalk
 
TTQ B4U said:
Perhaps humidity related? I've found it very easy. Spray, wipe, buff. When done with the entire car, I go back over and remove any streaks with a damp MF Rag with nothing but distilled water on it. Perfect shine and super slick. Based on this ease of use and longevity related abuse I've seen it being put through and surviving online, it's now my go-to top layer for basic Polish and Protects and over top of my AIO's I use.
Click to expand...

Maybe it’s cuz I’m not “buffing”. Seems like Reload/Clutch issues.

With Clutch they want you to let it set up for at least 15 min but leave on as long as you want. When I wait though it wipes right off


Sent from my iPhone using Tapatalk
 
Gave it a good long buff and looks good.

65266a94c94c84921daeec30b2eb96a6.jpg


af505801a5c057ba309b4791d87057e2.jpg
 
Questions for users:

How much are you using on a panel?

How long has this product been out?


Sent from my iPhone using Tapatalk
 
Coatingsarecrack said:
Maybe it’s cuz I’m not “buffing”. Seems like Reload/Clutch issues.

With Clutch they want you to let it set up for at least 15 min but leave on as long as you want. When I wait though it wipes right off


Sent from my iPhone using Tapatalk
Click to expand...

Did you not wipe it off after the application and let it sit for almost 2 hours?

What I have gotten from seeing application and have not used mine yet. Is that you would work in smaller sections. And use very sparingly and wipe it off directly after application. It's useally also cleans up the haze the first wash you do if you used a little to much or didn't been able to buff it off.
 
SWETM said:
Did you not wipe it off after the application and let it sit for almost 2 hours?

What I have gotten from seeing application and have not used mine yet. Is that you would work in smaller sections. And use very sparingly and wipe it off directly after application. It's useally also cleans up the haze the first wash you do if you used a little to much or didn't been able to buff it off.
Click to expand...

I used 4 sprays on half a hood. I’m guessing to much? Even with heavy application I haven’t had that tough of problem with removal (Clutch was close) Tried 4 towels. Last one was creature edgeless. Maybe it’s because it has wax but most sealants I’ve used wipe on wipe off. This took some actually buffing but again I may have used too much product. It’s fine after a little elbow grease

I’m not trying to knock the product, just giving my experience. Shine Supply Clutch is finicky if you try to wipe away too soon and even let it “set up” for an hour you may need to use a damp towel or QD to wipe. I love the stuff.

Just giving my experience and time will tell if I like it.

Just use to cosmic and overcoat lately and stuff’s WOWO.




Sent from my iPhone using Tapatalk
 
^^You tried buffing off immediately after spreading or did you wait extended time to buff off (was SWETM’s question)?
 
The only time I have had issues with ICE Spray Wax was when I did not wipe it off quickly. Just re-apply and wipe off in those cases.

I usually use it liberaly, spraying over entire pannel then using 2 towels to wipe off.

So far it's been a great product.

I was a bit disapointed in the durability of the Black Spray Wax from the test Jimbo did. I was expecting it to have similar durability to the ICE line. Unfortunatelly it really isn't as resillient.
 
acuRAS82 said:
^^You tried buffing off immediately after spreading or did you wait extended time to buff off (was SWETM’s question)?
Click to expand...

I applied and wiped off right away per instruction.


Sent from my iPhone using Tapatalk
 
An update on the companion product to Seal N Shine, the ICE Spray Detailer......

I had a small bird bomb on my quarter panel when I got off work. It was in the direct sunlight, 85+ and high humidity, I misted it on the bomb and the surrounding area and wiped it off. Not a streak or smear anywhere. I was impressed.
 
Since the mods are allowing this discussion to continue I’ll chime in with my directions for my best results. Spray lightly on a microfiber applicator, spread normally, wipe thoroughly, wash with McKees 914. The wash step is important to bring out the majority of the gloss. I scrubbed the heck out of it, but a simple wash is the easiest way.

I’m going to get some TW Quick Detailer and see if that will substitute for the wash step.
 
rlmccarty2000 said:
Since the mods are allowing this discussion to continue I’ll chime in with my directions for my best results. Spray lightly on a microfiber applicator, spread normally, wipe thoroughly, wash with McKees 914. The wash step is important to bring out the majority of the gloss. I scrubbed the heck out of it, but a simple wash is the easiest way.

I’m going to get some TW Quick Detailer and see if that will substitute for the wash step.
Click to expand...

When applying this to a clean surface, as most everyone does, what's the point of hitting it with N914 when you done applying it?
 
Coatingsarecrack said:
Not issues.... issue

I applied to applicator wiped on wiped off.....
unless it is different than the vast majority
of sealants out their....

Maybe 4 sprays to much but I have not
had problems removing ANY other product
I applied.
Click to expand...
•IMO:
-Yes it was ”issues”.

This time around you not only conveniently
left out this set of original “issues”:
“Did second coat 1.45 hours later
and found 1st coat hadn’t dried.
Buffed off but still streaking”.

But you added this “new issue”:
Coatingsarecrack said:
Feels “greasy”
Click to expand...

As such:
I’m still going to go with my
previous posting; that being:
FUNX650 said:
Just curious:
All these “issues”—yet adhering
to the product’s instructions?

:confused:
Click to expand...


Bob
 
How about temp and more importantly HUMIDITY

Sent from my SM-G950U using Tapatalk
 
FUNX650 said:
•IMO:
-Yes it was ”issues”.

This time around you not only conveniently
left out this set of original “issues”:
“Did second coat 1.45 hours later
and found 1st coat hadn’t dried.
Buffed off but still streaking”.

But you added this “new issue”:


As such:
I’m still going to go with my
previous posting; that being:



Bob
Click to expand...

Nope one issue 1st coat hard to remove, second coat was hard to remove. Was hard to remove. If I said something like left high spots.... then issues....

It feeling greasy was just observation not an issue


Sent from my iPhone using Tapatalk
 
Maybe I got a bunk bottle? Can someone post a pic of little of it. I will do same once I’m home. I’ve been thinking that maybe because it has wax needs more buffing?

Haven’t used anything with wax in it for 15 years.


Sent from my iPhone using Tapatalk
 
You must log in or register to reply here.
Back
Top