Hot day at The Bays Wheeling

So headed off @8:15 a.m. this morning, temperature...84 degrees and muggy...YEA
Here's product starting line-up:
Tires & Wheels
------------
-Griot's Garage 3 in 1 Tire/Wheel/Mat Cleaner
-All brushes
-TAC System Water Flow
-ADS Tire+
Engine Bay
---------
-Griot's Garage Engine Cleaner
-Designated brush
-Koch Chemie Mp
Car Wash & Decon
---------------
-ADS Shampoo+
-Griot's Garage Iron Remover
Interior & Exterior Glass
--------------------
-ADS Pilot
-Griot's Garage Stinky Be Gone Redline Cherry
-Shop-Vac
-CarPro Clarify Phobics
L S P
----
-Gyeon Q2 Wax
So I started with the Griot's Garage 3 in 1 Tire/Wheel/Mat Cleaner, 2 tires and wheels at time and all brushes used. The tires & wheels weren't dirty at all, infact they were freshly dressed yesterday but I still scrubbed everything and I'll say the ADS Ghost/Tire+ combo stood their ground here. I finished the wheels with a boost of TAC SystemWaterFlow and sorayed it on the grill and lower, black pieces as well as rear diffuser
Up next was the engine bay and it didn't require too much work as I stay ontop of it but I did a more deep clean and detail. I grabbed the Griot's Garage engine cleaner and designated brush (brissels were falling out as I used this old brush) I then grabbed my IK Sprayer filled with water to rinse down the entire engine bay as the cleaner was used everywhere. Next was the EGO dryer, gotta get one of these! I finished by applying Koch Chemie Mp on all plastic & and rubber bits, closed the hood and got ready for the next step
Up next was chemical decon. Now I don't expect anyone to remember what saw last month but a little Turtle Wax Rapid Decon wheel cleaner got on my fender and it bled, so I decided to chemically decon the whole car. After 5 mins I noticed very little "bleeding", mostly on vertical section of the trunk, almost not worth it but I did it. Without removing it I simply foamed the entire car w/ ADS Shampoo+, let dwell and rinsed away. Upon rinsing the beads...O M G ! I finished up using the EGO Blower to dry the car and then moved it over to the detail area
Once in the detail area I opened the hood and dried up the Koch Chemie Mp with a designated mf towel and got ready to start my detail
I started with the glass and I just love CarPro Clarify Phobics, key here is a little water on the glass and less is more...VERY key here when using CarPro Clarify Phobics but my God does this product work, it's basically a glass coating disguised as a glass cleaner

Next was the 1st of two coats of ADS Tire+, I hate the word SYNERGY but it applies here! Yes the ADS Ghost is there and present but there's NO denying a freshly dressed tire and my God do they look awesome
Now it's time to go "Old School" with the LSP/coating "booster" and for this I reached for Gyeon Q2 Wax, a product that came out a couple years ago and specifically made to be applied ontop of a ceramic coating. I applied it to the entire car, letting it sit as I moved to the interior detail
For the interior a quick vac with their Shop-Vac was done quickly. I then grabbed the ADS Pilot and Colourlock interior brush on all Alcantara bits and it worked like the champ it is! This brings up the Alcantara fibers, making them feel amazing and actually looks great as well, what an amazing versatile product because I then used ADS Pilot on the rest of EVERYTHING in the interior, what an absolute pleasure to use
I then sprayed Griot's Garage Stinky Be Gone Redline Cherry scent on all carpeted mats and at this point the interior was done
Finishing up was removing the Gyeon Q2 Wax which was on the paint for about an hour, per directions IIRC and besides, it was so muggy in there it needed to set up anyways. That said, not only did it come off easy but the GLOSS here...WOW!! Yes it's more work but applying it thin, as you should, made removal SO EASY & SO REWARDING
The EN is now across the street, under the shade tree and is NOT going into its usual parking spot, that Gyeon Q2 Wax is going to properly cure and no touch-free wash before work tomorrow either (maybe after work) because I want the best cure time for it
Thank you if you read this and/or looked at all the pics
Sent from my SM-G991U using Tapatalk